Does your band sound its best?
Author: Audiorent.co.uk
When you are a new band, playing live is nerve wracking enough
without having to worry about the front of house sound. Surely
it’s
enough to be concerned about whether your finely crafted and highly
practised material will stand up to public scrutiny, or if
you’ll
make
a tube of yourself by falling off the stage in front of the gathered
mass of friends and family. Very important things both, but there are a
number of simple things you can do to help yourselves and the sound
engineer ensure you have the best possible sound coming through the PA.
With that sorted you can worry less about the sound and more about
whether you look like a tool in your new skinny jeans and winkle
pickers.
First and most importantly arrive on time, en masse and fully equipped
for your sound check. The sound check is as important as the live
performance as this is the time the sound engineer will tune the PA
system to get the best from your performance. He will tweak the system
to suit your style of music, vocals and tone as well as familiarise
himself with your set-up and any requirements you may have that are
slightly out of the ordinary. It’s no good showing to your
first
gig
five minutes before you are due to go on with an unexpected twelve
piece choir and full brass section and expect the engineer to
accommodate them and get them sounding their best. No doubt he will do
his best, but the sound may not be as good as it could be and your
performance may suffer as a result. Arriving on time will allow you to
have a relaxed and thorough sound
check, to solve any little problems that might come up and for you to
familiarise yourselves with the venue and stage layout.
Discuss your sound and how you want to come across to the audience with
the sound engineer during your soundcheck. More than likely he will
have never have heard you before and so will not know what sort of mix
you require, so cannot be expected to magically guess what you want to
sound like. You may not be able to get the exact sound your after due
to limitations in the PA, poor acoustics in the venue or any number of
reasons. But if you are on time, polite and constructive when
addressing the engineer he will do his best to get you sounding as good
as is possible with the equipment available to him and will more than
likely look forward to working with you again.
Another tip is to consider your on-stage amplification purely as
monitoring for yourselves and only turn them up loud enough for you to
comfortably hear them. You may be used to winding your amps up to
eleven in the practice studio, but doing that during a live performance
can cause a number of problems. Firstly the sound engineer will have
mic’ed the amps up and as such will be controlling
they’re
sound
through the PA. The louder you have your amps on stage, the lower he
has to have them through the PA and the less control he has over the
overall sound mix, so you have a slightly messy and disjointed sound
out front. Secondly, you will have on-stage monitoring so you can hear
you vocals, as such the louder you have your amps, the louder the
monitors have to be for you to hear yourselves. This increases the risk
of feedback and can result in a slightly messy and disjointed sound on
stage. So overall that’s a slightly messy and disjointed
sound
out
front and on-stage and with everybody struggling to hear
what’s
going
on everywhere. Not good. Trust the engineer to make the most of your
sound out front and leave the volume dial on your amps alone. One way
of improve your ability to monitor your amps is by sticking them on
crates so they are closer to your ears and not pointing directly at
your legs.
The tone of your amps can also prove to be problematic. Excessive
treble will carry through the PA and result in a nasty jangly sound.
This excessive top end is not always noticed by bands as by the time
the sound has reached them from the amp it is ok, but bear in mind the
position of the instrument mic. If you listen to your amp from the
proximity of the mic, you’ll be surprised by how much more
treble
is
evident. Adjust the settings on the amp from the position of the mic to
get the best sound through the PA system.
Bad microphone technique is a common issue and can have a derogatory
effect on the production of your vocals. Dynamic unidirectional vocal
microphones of the type predominantly used for live vocals have a very
specific area in which they pick up sound, usually within a couple of
inches of the mic head. This design feature is to reduce the likelihood
of other noises being picked up from around the stage helping to
produce a cleaner sound and reduced chance of feedback. To get the
optimum sound from the mic, try and keep within a couple of inches of
the head, sing clearly and don’t move your head excessively
when
singing. This way, a fairly consistent signal will be picked up by the
mic and your vocal won’t appear to be fading in and out.
Also,
try not
to cup your hand over the mic head or hold the mic’ upside
down
as this
will more than likely cause feedback.
Positioning yourself correctly on the stage can have a positive impact
on your sound. More than likely you’ll have been trapped
three
feet
apart from each other in a sweaty, rehearsal studio for weeks
previously, so when faced with a nice, big stage, the temptation to get
as far away from each other as possible is understandable. But try and
stay compact on stage, particularly if you are only a small band, as
this will not only help you hear each others amps better for monitoring
purposes but will also prevent you looking and sounding disjointed and
appear more of a cohesive unit.
Lastly, there are certain items that you should always remember as
although the engineer may be able to help supply you with them, do not
expect him to. There may be a time when he cannot and that may leave
you in a pickle.
• Drum mat – a vital addition to your
drummer’s gear.
Without it the
kit will make its way slowly across the stage and into the audience.
Lack of a mat usually results in the extensive use of the sound
guy’s
vital and surprisingly expensive gaffer tape to secure the kick drum.
• Electrical adaptors – ensure you have sufficient
extension
reels and
adaptors to support all you gear. The engineer may only have enough to
cover the PA equipment so, again if you really have to plug in all
fourteen of you effects pedals make sure you have sufficient power
supplies to do so.
• Audio cables and adaptors – make sure you have
enough
guitar leads
(including spares in case of breakdown), as again the engineer may not
carry spares. Also if you are plugging in keyboards, click tracks or
decks have the correct leads or adaptors to plug them into the PA
–
usually either ¼ inch jacks or XLR.
• To be nice to the engineer – He will have been
there four
hours
before you mucking around with cables and lugging heavy equipment
around to make you sound half decent and will be there two hours after
you’ve disappeared down the pub to muck around with cables
and
lug
heavy equipment around, so be nice.
Professional PA hire companies such as Audiorent.co.uk have highly
experienced, professional and approachable engineers who will be more
than happy to discuss any aspect of your set-up or performance. It is
the engineer’s job to get the best from your music and ensure
that the
audience can focus on your performance rather than any anomalies in the
sound, so if you follow the simple tips given above the chances of that
are greatly increased.
If you need any information about the hire of PA equipment for your
bands live performances or any aspect of PA, lighting, backline or AV
hire in Nottingham and throughout the UK, contact Audiorent.co.uk on contact@audiorent.co.uk
or call us on 07951164194.
Audiorent.co.uk is a professional PA hire company supplying PA, lighting, backline and AV equipment for all conceivable events.
Article Source: ArticlesBase.com - The New Bands Guide to Getting the Best From Their Live Sound
What's Up?
Tell me here!

